Debian Bitcoind CryptoCoins Info Club

A Guide to Keeping Keys Offline Using Armory +rPi

Hi Redditors.
I am going to post in this thread my experiences in getting my Desktop (Debian) machine running Armory in watch-only mode, and coupling that with an offline Raspberry Pi (which holds my private keys) for signing the transactions previously made in watch-only mode.
I actually compiled Armory from source directly on my Pi. This guide is probably more for the bitcoin 'power user', as to run Armory online, and broadcast the signed transactions, you need to have a bitcoin full node running (bitcoind).
Basic requirements:
Aimed-for Setup:
I'll post the guide in digestible sections...

Section 1

I should begin by saying I installed source code from git, and got Armory to build the DB on my desktop initially, WITHOUT creating a wallet.. (This allowed me to debug what was going on a little!)
Go to Bitcoin.org, select Armory..
It leads to a Download from Git:
https://github.com/goatpig/BitcoinArmory/releases
Followed the procedure for Linux Debian verify code, compile, install, all straight-forward..
Began by running bitcoind, and telling Armory where to find it. This is the command I used, obviously it was all on one line and didn't include the arrows/explanations!:
python ArmoryQt.py \ --satoshi-datadir=/BlockChain/chain20180414/blocks \ # <-----(where my bitcoind blocks live) --datadir=/ArmoryDataDi \ # <-----(this is instead of ~/.armory) --dbdir=/ArmoryDataDidatabases # <-------(again, non std. place used for Armory's databases.. my choice.) 
So, on the Desktop, after the initial "build databases"
(NB the initial "Build Databases" took about 1.5h and my two CPUs were maxed the whole time, Temps up to 62C. Not ideal; Im not in a rush!)
I then wanted to import a watch-only wallet.
Before I did this, I took a full backup of the Armory data dir:
/ArmoryDataDi
(or ~/.armory in a default installation).
I'd hate to have to make Armory do another full sync with the bitcoind node!

Section 2

Next step: offline wallet (with Private Keys) is on a Raspberry Pi.
I downloaded the source and managed to compile it on the pi itself! :)
Though there were some gymnastics needed to setup the Pi.
My Pi is running Raspbian based on Wheezy.. quite old!
I did the following on the Pi:
apt-get update apt-get upgrade (<---took about an hour!) apt-get install autotools-dev apt-get install autoconf 
Then I followed the instructions exactly as I had done for my Debian Desktop machine, EXCEPT:
I had to increase the Pi's swap space. I upped it from 100Mb to 400Mb.
The compilation took 7 hours, and my poor SD card got a thrashing.
But after compilation, I put the Swap back to 100Mb and Armory runs ok with about 150Mb of memory (no swap needed).
Swap increase on the Pi:
use your favourite editor, and open the file /etc/dphys-swapfile
add/change the following line:
CONF_SWAPSIZE=400 
Then, REBOOT the Pi:
sudo shutdown -h -P now 
Once the compilation was done on the Pi, put the swap back, rebooted and created an Armory wallet.
I added manual entropy and upped the encryption 'time' from 250ms to 2500ms - since the Pi is slow, but I'll be happy to wait for more iterations in the Key Derivation Function.
Once the wallet was created, it obviously prompts you for backup.
I want to add a private key of my own (i.e. import), so don't do the backup until this is over.
I import my Private Key, and Armory checks that this corresponds to a Public Key, which I check is correct.
This is the point now where the Pi storage medium (e.g an SD card) has to be properly destroyed if you ever get rid of it.
I had thought that now would be a good time to decide if your new wallet will generate Segwit receiving addresses, and also addresses used to receive 'change' after a transaction..
But it seems Armory WON'T let you switch to P2SH-P2WPKH unless your Armory is connected to a node offering "WITNESS" service.
Obviously, my Pi is offline and will never connect to a node, so the following will not work on the Pi:
NB: I thought about setting this on the Debian "watch-only" wallet, but that would surely mean doom, as the Pi would not know about those addresses and backups might not keep them.. who knows...
So, end result:- no segwit for me just yet in my offline funds.

--If anyone can offer a solution to this, I'd be very grateful--

Section 3

Ok, now this is a good point to back up your wallet on the Pi. It has your imported keys. I choose a Digital Backup - and put it on a USB key, which will never touch the internet and will be stored off-site. I also chose to encrypt it, because I'm good with passwords..
NB: The Armory paper backup will NOT back up your imported private keys, so keep those somewhere if you're not sweeping them. It would be prudent to have an Armory paper backup anyway, but remember it will likely NOT help you with that imported key.
Now for the watch-only copy of the wallet. I want to get the "watch-only" version onto my Desktop Debian machine.
On the Pi, I created (exported to a USB key) a "watching-only" copy of my wallet.
I would use the RECOMMENDED approach, export the "Entire Wallet File".
As you will see below, I initially exported only the ROOT data, which will NOT capture the watching-only part of the Private Key I entered manually above (i.e. the public Key!).
Now, back on the Debian Desktop machine...
I stopped all my crontab jobs; just give Armory uninterrupted CPU/memory/disk...
I also stopped bitcoind and made a backup prior to any watch-only wallet being imported.
I already made a backup of Armory on my Desktop, before any wallet import.
(this was needed, as I made a mistake.. see below)
So on the Debian Desktop machine, I begin by firing up bitcoind.
my command for this is:
./bitcoind -daemon -datadir=/BlockChain/chain20180414 -dbcache=400 -maxmempool=400 

Section 4

I try running Armory like this:
(I'm actually starting Armory from a script - StartArm.sh)
Inside the script StartArm.sh, it has the line:
python ArmoryQt.py --ram-usage=4 --satoshi-datadir=/BlockChain/chain20180414/blocks --datadir=/ArmoryDataDi --dbdir=/ArmoryDataDidatabases 
I know from bitter experience that doing a scan over the blockchain for a new wallet takes a looong time and a lot of CPU, and I'd like it to play nicely; not gobble all the memory and swap and run my 2xCPUs both at 100% for four hours...
So... I aim to run with --ram-usage=X and --thread-count=X
(For me in the end, X=1 but I began with X=4)
I began with --ram-usage=4 (<--- = 4x128Mb)
The result is below...
TypeError: cannot concatenate 'str' and 'int' objects 
It didn't recognise the ram-usage and carried on, crippling my Debian desktop PC.
This is where it gets dangerous; Armory can gobble so much memory and CPU that the windowing environment can cease up, and it can take over 30 minutes just to exit nicely from bitcoind and ArmoryDB.
So, I ssh to the machine from another computer, and keep an eye on it with the command
"free -h" 
I'd also be able to do a "sudo reboot now" if needed from here.

Section 5

So, trying to get my --ram-usage command recognised, I tried this line (added quotes):
python ArmoryQt.py --ram-usage="4" --satoshi-datadir=/BlockChain/chain20180414/blocks --datadir=/ArmoryDataDi --dbdir=/ArmoryDataDidatabases 
But no, same error...
Loading Armory Engine: Armory Version: 0.96.4 Armory Build: None PyBtcWallet Version: 1.35 Detected Operating system: Linux OS Variant : ('debian', '9.4', '') User home-directory : /home/ Satoshi BTC directory : /BlockChain/chain20180414 Armory home dir : /ArmoryDataDi ArmoryDB directory : /ArmoryDataDidatabases Armory settings file : /ArmoryDataDiArmorySettings.txt Armory log file : /ArmoryDataDiarmorylog.txt Do wallet checking : True (ERROR) ArmoryUtils.py:3723 - Unsupported language specified. Defaulting to English (en) (ERROR) ArmoryQt.py:1833 - Failed to start Armory database: cannot concatenate 'str' and 'int' objects Traceback (most recent call last): File "ArmoryQt.py", line 1808, in startArmoryDBIfNecessary TheSDM.spawnDB(str(ARMORY_HOME_DIR), TheBDM.armoryDBDir) File "/BitcoinArmory/SDM.py", line 387, in spawnDB pargs.append('--ram-usage=' + ARMORY_RAM_USAGE) TypeError: cannot concatenate 'str' and 'int' objects 

Section 6

So, I edit the Armory python file SDM.py:
if ARMORY_RAM_USAGE != -1: pargs.append('--ram-usage=4') #COMMENTED THIS, SO I CAN HARDCODE =4 # ' + ARMORY_RAM_USAGE) 
Running it, I now have acknowledgement of the --ram-usage=4:
(WARNING) SDM.py:400 - Spawning DB with command: /BitcoinArmory/ArmoryDB --db-type="DB_FULL" --cookie --satoshi-datadir="/BlockChain/chain20180414/blocks" --datadir="/ArmoryDataDi" --dbdir="/ArmoryDataDidatabases" --ram-usage=4 
Also, even with ram-usage=4, it used too much memory, so I told it to quit.
It took over 30 minutes to stop semi-nicely. The last thing it reported was:
ERROR - 00:25:21: (StringSockets.cpp:351) FcgiSocket::writeAndRead FcgiError: unexpected fcgi header version 
But that didn't seem to matter or corrupt the Armory Database, so I think it's ok.
So, I get brave and change SDM.py as below, and I make sure my script has a command line for --ram-usage="ABCDE" and --thread-count="FGHIJ"; the logic being that these strings "ABCDE" will pass the IF criteria below, and my hardcoded values will be used...
if ARMORY_RAM_USAGE != -1: pargs.append('--ram-usage=1') #COMMENTED THIS, SO I CAN HARDCODE =1 # ' + ARMORY_RAM_USAGE) if ARMORY_THREAD_COUNT != -1 pargs.append('--thread-count=1') #COMMENTED THIS, SO I CAN HARDCODE =1 #' + ARMORY_THREAD_COUNT) 
So, as usual, I use my script and start this with: ./StartArm.sh
(which uses command line:)
python ArmoryQt.py --ram-usage="ABCDE" --thread-count="FGHIJ" --satoshi-datadir=/BlockChain/chain20180414/blocks --datadir=/ArmoryDataDi --dbdir=/ArmoryDataDidatabases 
(this forces it to use my hard-coded values in SDM.py...)
So, this is the command which it reports that it starts with:
(WARNING) SDM.py:400 - Spawning DB with command: /BitcoinArmory/ArmoryDB --db-type="DB_FULL" --cookie --satoshi-datadir="/BlockChain/chain20180414/blocks" --datadir="/ArmoryDataDi" --dbdir="/ArmoryDataDidatabases" --ram-usage=1 --thread-count=1 
Again, this is where it gets dangerous; Armory can gobble so much memory and CPU that the windowing environment can cease up. So I ssh to the machine and keep an eye on it with:
"free -h" 

Section 7

So, on the Debian Desktop PC, I inserted the USB stick with the watch-only wallet I exported from the Pi.
Start Armory...
Import "Entire Wallet File" watch-only copy.
Wait 4 hours..
YAY!!!
After running Armory for about 30m, the memory usage dropped by 400m... wierd...
It took ~2 hours to get 40% completion.
After 3.5 hours it's almost there...
The memory went up to about 1.7Gb in use and 900Mb of Swap, but the machine remained fairly responsive throughout, apart from a few (10?) periods at the start, where it appeared to freeze for 10-30s at a time.
(That's where my ssh session came in handy - I could check the machine was still ok with a "free -h" command)
Now, I can:
Create an unsigned transaction on my Desktop,
Save the tx to USB stick,
Move to the Pi,
Sign the tx,
Move back to the Desktop,
Broadcast the signed tx.

Section 8

My initial Mistake:
This caused me to have to roll-back my Armory database, using the backup. so you should try to avoid doing this..
On the Pi, I exported only the ROOT data, which will NOT capture the watching-only part of the Private Key
It is RECOMMENDED to use the Digital Export of Entire Wallet File from the Pi when making a watch-only copy. If you just export just the "ROOT data", not the "Entire Wallet File", you'll have problems if you used an imported Private Key in the offline wallet, like I did.
Using the ROOT data text import, after it finished... my balance was zero. So,. I tried a Help->Rescan Balance (Restart Armory, takes 1minute to get back up and running) No Luck. Still zero balance.
So, I try Rescan Databases.. This will take longer. Nah.. no luck.
So, I tried again, thinking it might be to do with the fact that I imported the text "root data" stuff, instead of following the (Recommended) export of watching-wallet file.
So, I used my Armory backup, and wound back the ArmoryDataDi to the point before the install of the (zero balance) wallet. (you should not need to do this, as you will hopefully use the RECOMMENDED approach of exporting the "Entire Wallet File"!)
submitted by fartinator to Bitcoin [link] [comments]

Help please, Staking reddcoin on Raspberry Pi (Raspbian Stretch with desktop)

Hello,
I could really use some help setting up a reddcoin wallet on the Raspberry pi. I've tried executing the following 2 guides, but unfortunatly they keep giving me errors. Guide1: https://www.reddit.com/reddCoin/comments/2b8wqm/tutorial_compiling_and_running_the_reddcoin/ Guide2: http://d-lindemann.de/2017/09/reddcoin-staking-mit-raspberry-pi/
instead of using the recommended "Raspbian (Debian Wheezy). The image file name is 2014-06-20-wheezy-raspbian.img." i'm using the latest " Raspbian Stretch with desktop Image with desktop based on Debian Stretch Version: November 2017 Release date: 2017-11-29 Kernel version: 4.9"
Also instead of using Reddcoin v1.3.1.2 i decided to go with the* Reddcoin V2.0.0.0 (latest version todate)*
every step untill step 6 seems to work fine, but then after executing command: make -f makefile.unix" the following error message appears:
make: makefile.unix: No such file or directory make: *** No rule to make target 'makefile.unix'. Stop.
researching that issue led me to abandon the guide1 and move to a more recent version of a guide. https://github.com/joroob/reddcoin/blob/mastedoc/rasp-tut.md following those steps lead to a bignum error at 6.3 after excecuting commands
cd src (to take me to reddcoin/src) make (to start compiling i assume)
the bignum error i'm experiencing now seems to be described very well here: https://github.com/reddcoin-project/reddcoin/issues/103 In there i excecuted the following commands to see if my dependencies were correct.
sudo apt-get build-essential   sudo apt-get install build-essential   sudo apt-get install libtool autotools-dev autoconf   sudo apt-get install libssl-dev   sudo apt-get install libboost-all-dev   sudo add-apt-repository ppa:bitcoin/bitcoin sudo apt-get update sudo apt-get install db4.8 sudo apt-get install libdb4.8-dev sudo apt-get install libdb4.8++-dev sudo apt-get install libminiupnpc-dev sudo apt-get install libqt4-dev libprotobuf-dev protobuf-compiler sudo apt-get install libqrencode-dev cd reddcoin .>/autogen.sh ./configure make
However this did not seem to clear my issue. reading on they talk about it being an issue with libssl in debian 9. with the following link. (at this point i'm noticing how the further i go, the less ground is beneath me to stand on.. and i'm not a good swimmer in unix).
anyways final post there says the following code should fix it: https://github.com/peercoin/peercoin/commit/5b09830e5de0f5105534e69dbf4acffb3255869b But what do i do with this link i have no idea. and that's kinda where my progress halts as i cannot for the life of me find out what to do next to troubleshoot this issue.
So TL:DR I'm trying to use the make command in ~/reddcoin/src however it's giving me BIGNUM errors preventing me from making progress.
I'm using PI model B+, Raspbian stretch latest version plz halp...
submitted by FloydStash to reddCoin [link] [comments]

[Guide] Setting up Trezor + Electrum 2.02beta + armory on a Raspberry Pi 2. Cold offline signing for $40

Having just received my Pi 2, I am happy to report that a fresh Raspbian install, on an 8 GB Class 10 MicroSD card : Electrum / Armory / Trezor / BTChip all work with my Single Board Computer setup script (it also works for Pi B, Pi B+ Raspbian and BeagleBone Black Debian & ubuntu, also tested on Odroid C1 Ubuntu 14.4)
The full "!" installation takes about 40 mins on Pi 2, which is at least twice as fast as on the Pi B+ / BBB
Notes
submitted by Aussiehash to Bitcoin [link] [comments]

Debian Wheezy install last flash plugin version 1080p - Howto Debian Wheezy/Testing Xfce Desktop from scratch - Part 1 of 3 Linux Debian 7 Wheezy (RC -- Testing release) installation demo Linux Debian Wheezy 7.8 : DNS SERVER Installation Debian Wheezy - Netinstaller / LAMP - Teil 1 German

This tutorial explains how to install and use Bitcoin Core on Debian Linux. Bitcoin Core is the official Bitcoin Wallet from bitcoin.org. I will use the latest version from the GIT repository at bitcoin.org. In order to compile and run, Bitcoin Core depends on some other tools which must be installed prior to compiling : Bitcoin Classic ships both a background application (called daemon in Linux) bitcoind and a graphical application bitcoin-qt, you will have to choose one to run.The daemon version of Bitcoin Classic can run without graphics systems installed on the system and the only way to interact with it is to use the command line . trending; Debian Bitcoind Bitcoin . Debian Bitcoind . Apr 12, 2018 DTN ... Install Bitcoin Core to Debian Wheezy January 18, 2015 01:39AM Registered: 5 years ago Posts: 1 I downloaded Bitcoin ... The release is built with GCC and then "strip bitcoind" to strip the debug symbols, which reduces the executable size by about 90%. miniupnpc ----- tar -xzvf miniupnpc-1.6.tar.gz cd miniupnpc-1.6 make sudo su make install Berkeley DB ----- It is recommended to use Berkeley ... Install Bitcoin On Debian This past week I took a few hours to get a Bitcoin full node running on my Debian server. Qt Wallet On Debian 7 How To Compile And Install Bitcoin ..Install the Litecoin-qt. This operation differs by operating system:Don't use "-j4" for this build. Once that completes, then run:. We are going to run a Bitcoin full node in a Debian system (Sid) $ wget Install the binaries in /usr/local/bin directory $ sudo install -m 0755 -o root -g root -t /usr/local/bin bitcoin-0.14.2/bin/* By now we are going to run only Bitcoin daemon with no graphical interface: NOTE: you can execute $ bitcoind -server to

[index] [31177] [9347] [38235] [48837] [19159] [8246] [24991] [14941] [11770] [19102]

Debian Wheezy install last flash plugin version

ملاحظه : Sid Hocine تعليق مميز قام في هذا درس بتحديث سورسات لكن هونا يجب انتباه ايضا لاصدار كالي اول او ثاني او ... How to install Debian for a xfce desktop environment that looks like old gnome2. This three part tutorial will walk you through a 20-50 MB base install. From there you will upgrade your system to ... Ich zeige euch hier wie man mittels Debian Netinstaller Debian installiert. In den folgenden Schritten / Videos richten wir schließlich einen kompletten LAMP Server ein. Part 2 -- A step by step tutorial how to do a Debian install for the desktop. Starting with a 20 MB image we will build a bloatless non Gnome free environment from scratch. How to install Debian ... This video shows how easy it is to install and run Bitmessage on Debian 7.0 (Wheezy) Installation commands: apt-get install python openssl git python-qt4 git...

#